Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. General information
8.2. External elements of a body
8.3. System of passive safety
8.3.1. General information
8.3.2. Precautionary measures
8.3.3. Electric system
8.3.4. The module of a safety cushion and the device for a naduvaniye of an airbag (gas generator)
8.3.5. Plait of wires of SRS
8.3.6. Activation of a control lamp of SRS
8.3.7. Hour spring
8.3.8. System of definition of presence of the passenger on a forward seat (PPD)
8.3.9. Sensor of lateral blow
8.3.10. Removal and check of the module of a face-to-face safety cushion of the driver (DAB)
8.3.11. Removal of the module of a safety cushion of the passenger (PAB)
8.3.12. Prednatyazhitel of seat belts (gas generator)
8.3.13. Removal of a prednatyazhitel
8.4. Heater and conditioner
8.5. Tables
9. Electric equipment schemes
 







8-3-10-snyatie-i-proverka-modulya-frontalnojj-podushki-bezopasnosti-voditelya-dab.html

8.3.10. Removal and check of the module of a face-to-face safety cushion of the driver (DAB)

Module of a face-to-face safety cushion of the driver (DAB)
Fig. 8.46. Module of a face-to-face safety cushion of the driver (DAB)



Removal

Removal of the negative plug of the storage battery
Fig. 8.47. Removal of the negative plug of the storage battery


Disconnect a wire from the negative plug of the storage battery and reliably заизолируйте I will corrode wires (fig. 8.47).

ATTENTION
Before the beginning of works after a detachment of a cable of the storage battery make a pause not less than 30 pages.


Removal of an overlay of a steering wheel
Fig. 8.48. Removal of an overlay of a steering wheel


Remove lateral covers of a steering wheel. Unscrew bolts of fastening of the module of a safety cushion (an internal shestigrannik) (fig. 8.48).

Removal of an hour spring
Fig. 8.49. Removal of an hour spring


Disconnect the socket of an hour spring from the pillow module, having pulled for a socket clamp outside (fig. 8.49).

ATTENTION
At a detachment of the socket do not apply considerable efforts.


Removal of the module of a safety cushion
Fig. 8.50. Removal of the module of a safety cushion


Remove the module of a safety cushion of the driver (fig. 8.50).

Removal of a steering wheel
Fig. 8.51. Removal of a steering wheel


Unscrew a nut of fastening and by means of a stripper (09561-11002) dismantle a steering wheel (fig. 8.51).

ATTENTION
Do not remove a steering wheel in the shock way: it is possible to damage the mechanism of folding of a column at collision.

Module check
If as a result of check any defective detail is found, replace the safety cushion module with the new.
The old safety cushion is subject to blasting on special procedure.

ATTENTION
Never try to measure resistance of an electrofuse of a pillow, even by means of a special tester: sudden blasting a pillow which will lead to accident is possible.

Check an overlay of the module of a pillow (a hollow, cracks, deformation).
Check the case of the module of a pillow (a hollow, cracks, deformation).
Check a socket condition (deformation of contacts, clamps, twisting of wires).
Check the inflatable module of a pillow (a hollow, cracks, deformation).
Establish the pillow module on a steering wheel for verification of the relative provision of a pillow and a steering wheel.

Check of an hour spring
If as a result of check any defective detail is found, replace an hour spring with the new.
Check a socket condition (deformation of contacts, clamps) and a protective tube.

«previous page
8.3.9. Sensor of lateral blow
following page»
8.3.11. Removal of the module of a safety cushion of the passenger (PAB)