Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
6.1. General information
6.1.1. Check and adjustment of a pedal of a brake
6.1.2. Check of operation of the vacuum amplifier of brakes without a tester
6.1.3. Air removal from a hydraulic actuator of brakes
6.1.4. Check and adjustment of a course of the lever of the parking brake
6.1.5. Removal and installation of the vacuum amplifier of brakes
6.1.6. Check of highways of brake system
6.1.7. Removal and installation of a pedal of a brake
6.1.8. Removal, check and installation of forward brake shoes
6.1.9. Dismantling, check and assembly of a brake support
6.1.10. Dismantling, check, assembly and installation of the main brake cylinder
6.1.11. Regulator of pressure of back brakes
6.1.12. Removal, check and installation of back drum-type brakes
6.1.13. Replacement of the working brake cylinder
6.1.14. Removal, check and installation of the parking brake
6.1.15. Anti-blocking system of brakes (ABS)
6.1.16. Removal and installation of the electronic ABS control unit
6.1.17. Removal and check of sensors of frequency of rotation of a wheel (ABS)
6.2. Tables
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 







6-1-8-snyatie-proverka-i-ustanovka-perednikh-tormoznykh-kolodok.html

6.1.8. Removal, check and installation of forward brake shoes

Forward disk brake
Fig. 6.18. Forward disk brake: 1–connecting tube (brake hose and tube assembled); 2–support of a forward brake assembled; 3–brake disk



Removal

Bolt of fastening of a support
Fig. 6.19. Bolt of fastening of a support


Unscrew the bottom bolt of a support, lift up and fix it a wire (fig. 6.19).
Take out brake shoes.

ATTENTION
At the removed brake shoes do not press a brake pedal.

Check
Measure thickness of a frictional layer of a block. Be convinced of lack of a zamaslivaniye of a block.

ATTENTION
Blocks of brakes of one bridge always replace at the same time. Do not establish a block of different types and manufacturers.

All four blocks are replaced with a set.
At replacement of blocks check absence of their deformation. At spring replacement carefully remove all dirt.

Brake shoes
Fig. 6.20. Brake shoes


Check old blocks on deformation and destruction (fig. 6.20).
Thickness of a block:
The nominal:    11 mm
The limiting:    2 mm

Installation
Establish in directing springs of a block.

Clamps of brake shoes
Fig. 6.21. Clamps of brake shoes


Establish clamps of brake shoes (fig. 6.21).

NOTE
The indicator of wear of a block should be directed up to the piston.


Piston installation in a support
Fig. 6.22. Piston installation in a support


By means of the special tool (09581-11000) get pistons in a support (fig. 6.22).

Components of brake shoes
Fig. 6.23. Components of brake shoes


Establish on laying blocks, as is shown in drawing 6.23.

ATTENTION
Do not allow greasing hit on blocks and a brake disk.


Installation of the bottom (directing) bolt of a support
Fig. 6.24. Installation of the bottom (directing) bolt of a support


Establish the bottom (directing) bolt of a support and tighten it the regulated moment (fig. 6.24).
Moment of an inhaling of 22-32 N · m.

«previous page
6.1.7. Removal and installation of a pedal of a brake
following page»
6.1.9. Dismantling, check and assembly of a brake support