Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
6.1. General information
6.1.1. Check and adjustment of a pedal of a brake
6.1.2. Check of operation of the vacuum amplifier of brakes without a tester
6.1.3. Air removal from a hydraulic actuator of brakes
6.1.4. Check and adjustment of a course of the lever of the parking brake
6.1.5. Removal and installation of the vacuum amplifier of brakes
6.1.6. Check of highways of brake system
6.1.7. Removal and installation of a pedal of a brake
6.1.8. Removal, check and installation of forward brake shoes
6.1.9. Dismantling, check and assembly of a brake support
6.1.10. Dismantling, check, assembly and installation of the main brake cylinder
6.1.11. Regulator of pressure of back brakes
6.1.12. Removal, check and installation of back drum-type brakes
6.1.13. Replacement of the working brake cylinder
6.1.14. Removal, check and installation of the parking brake
6.1.15. Anti-blocking system of brakes (ABS)
6.1.16. Removal and installation of the electronic ABS control unit
6.1.17. Removal and check of sensors of frequency of rotation of a wheel (ABS)
6.2. Tables
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 







6-1-5-snyatie-i-ustanovka-vakuumnogo-usilitelya-tormozov.html

6.1.5. Removal and installation of the vacuum amplifier of brakes

Vacuum amplifier of brakes
Fig. 6.9. Vacuum amplifier of brakes



Removal
Disconnect a brake tube from the main brake cylinder.

Nuts of fastening of the main brake cylinder
Fig. 6.10. Nuts of fastening of the main brake cylinder


Remove the main brake cylinder (fig. 6.10).

ATTENTION
At hit of brake liquid on the painted surfaces immediately wipe the spilled liquid.

Disconnect a vacuum hose from the amplifier of brakes.
Disconnect a pusher of the amplifier of brakes from a brake pedal.

Nuts of fastening of the vacuum amplifier of brakes
Fig. 6.11. Nuts of fastening of the vacuum amplifier of brakes


Unscrew nuts of fastening of the vacuum amplifier of brakes (fig. 6.11).
Lift the vacuum amplifier of brakes in collecting and remove it.

Installation
Before installation of the vacuum amplifier of brakes assembled check a condition of both laying of its arm of fastening, if necessary replace laying.
Establish the vacuum amplifier of brakes on a place and tighten fastening nuts.
Inhaling moment: 13–16 N · m.
Put enough of konsistentny greasing in an opening of the lever of a pedal of a brake (a pin installation site).

Connection of a fork of a pusher
Fig. 6.12. Connection of a fork of a pusher


Connect a pusher fork to the lever of a pedal of a brake by means of a pin with an opening under шплинт and fix a pin shplinty (fig. 6.12).
Establish the main brake cylinder. also connect to it a brake tube.
Connect a vacuum hose to the amplifier of brakes.
Fill with brake liquid a tank of hydrosystem of brakes.
Be convinced of absence of leakages of brake liquid.
Check and adjust the provision of a pedal of a brake.

Places of drawing of konsistentny greasing
Fig. 6.13. Places of drawing of konsistentny greasing


After installation of details put enough of konsistentny greasing in places of contact of a fork of a pusher and a brake pedal (fig. 6.13).

«previous page
6.1.4. Check and adjustment of a course of the lever of the parking brake
following page»
6.1.6. Check of highways of brake system