Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
6.1. General information
6.1.1. Check and adjustment of a pedal of a brake
6.1.2. Check of operation of the vacuum amplifier of brakes without a tester
6.1.3. Air removal from a hydraulic actuator of brakes
6.1.4. Check and adjustment of a course of the lever of the parking brake
6.1.5. Removal and installation of the vacuum amplifier of brakes
6.1.6. Check of highways of brake system
6.1.7. Removal and installation of a pedal of a brake
6.1.8. Removal, check and installation of forward brake shoes
6.1.9. Dismantling, check and assembly of a brake support
6.1.10. Dismantling, check, assembly and installation of the main brake cylinder
6.1.11. Regulator of pressure of back brakes
6.1.12. Removal, check and installation of back drum-type brakes
6.1.13. Replacement of the working brake cylinder
6.1.14. Removal, check and installation of the parking brake
6.1.15. Anti-blocking system of brakes (ABS)
6.1.16. Removal and installation of the electronic ABS control unit
6.1.17. Removal and check of sensors of frequency of rotation of a wheel (ABS)
6.2. Tables
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 







6-1-14-snyatie-proverka-i-ustanovka-stoyanochnogo-tormoza.html

6.1.14. Removal, check and installation of the parking brake

Contour of the parking brake
Fig. 6.54. Contour of the parking brake



Removal
Remove the back console.

Adjusting nut of the lever of a cable of the parking brake
Fig. 6.55. Adjusting nut of the lever of a cable of the parking brake


Weaken an adjusting nut and disconnect from the lever a cable of the parking brake (fig. 6.55).
Remove the switch of a control lamp of the parking brake.
Remove the lever of the parking brake assembled.
Remove a back wheel.
Remove a brake drum.
Remove brake shoes.

Cable detachment from a block of the parking brake
Fig. 6.56. A cable detachment from a block of the parking brake


Disconnect a cable from a block of the parking brake (fig. 6.56).

Ring of fastening of a cable to a basic brake disk
Fig. 6.57. A ring of fastening of a cable to a basic brake disk


Remove a ring of fastening of a cable to a basic brake disk (fig. 6.57).

Fastening клипс fixings of cables of the parking brake
Fig. 6.58. Fastening клипс fixings of cables of the parking brake


Unscrew fastening bolts клипс fixings of cables of the parking brake, remove cables assembled (fig. 6.58).

Check
Check operability of the switch of a control lamp of the parking brake.
Check a condition of a ratchet of the lever of the parking brake.
Estimate a condition of cables of the parking brake.

Installation

Color label of cables of the parking brake
Fig. 6.59. Color label of cables of the parking brake


Check color identification labels of cables of the parking brake. Connect cables according to labels (fig. 6.59).

Identification label
Left side: the red.
Right side: the yellow.

Top returnable spring
Fig. 6.60. Top returnable spring


At installation of the top returnable spring remove the regulator lever back (fig. 6.60).

Fastening of cables of the parking brake
Fig. 6.61. Fastening of cables of the parking brake


Fix cables of the parking brake, as is shown in drawing 6.61.
Grease a ratchet and a doggie of the lever of the parking brake with konsistentny greasing.
Establish a regulator of cables and adjust cables of a drive of the parking brake.

NOTE
The parking brake should work at the eighth click of a ratchet of the lever of the parking brake at the effort of 196 N attached to a point of the lever, 40 mm located at distance from the lever end.

«previous page
6.1.13. Replacement of the working brake cylinder
following page»
6.1.15. Anti-blocking system of brakes (ABS)