Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
2.1. Maintenance
2.1.1. Check of level of engine oil
2.1.2. Replacement of engine oil
2.1.3. Choice of the oil filter
2.1.4. Replacement of the oil filter
2.1.5. Check of tightness of system of cooling
2.1.6. Check of valves of a cover of a radiator
2.1.7. Check of concentration of antifreeze
2.1.8. Compression check
2.1.9. Adjustment of a tension of a belt of a drive of GRM
2.1.10. Drive of hinged units
2.1.11. Natyazhitel of a belt of a drive of hinged units
2.1.12. Adjustment of a belt of a drive of hinged units
2.1.13. Adjustment of a belt of a drive of the generator
2.2. Mechanical part (engine of 1,6 l)
2.3. Mechanical part (engine of 1.8 l)
2.4. Cooling system
2.5. Greasing system
2.6. Power supply system
2.7. Control system, fuel system and system of decrease in toxicity
2.8. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 







2-1-12-regulirovka-remnya-privoda-navesnykh-agregatov.html

2.1.12. Adjustment of a belt of a drive of hinged units

Correctness of landing of a belt in flutes of pulleys
Fig. 2.15. Correctness of landing of a belt in flutes of pulleys


Check correctness of landing of a belt in flutes of pulleys (fig. 2.15).
Make effort of 100 N the reverse (non-working) side of a belt in the middle of a branch between two pulleys. Measure a belt deflection by means of a tension measuring instrument.

ATTENTION
At installation of a poliklinovy belt be convinced of correctness of landing of racetracks of a belt in flutes of pulleys.

If at work the belt "squeals" or slips, check surfaces of contact to pulleys and a pulley on lack of wear, damage or stratification. Besides, check degree of a tension of a belt.

Contour of a belt of a drive of hinged units
Fig. 2.16. Contour of a belt of a drive of hinged units



NOTE
The tension of a belt is measured in the middle of a branch of a belt between the specified pulleys.
At installation of a new belt adjust a tension so that it corresponded to average value from an admissible range in a column «for a new belt» tables 2.2. After installation of a belt let's to the engine work during 5 mines or more long, then check compliance of a tension of a belt to nominal rate from a column «at check» tables 2.2.
At adjustment of the belt which was in operation or the new belt which has worked on the engine more than 5 mines, use the nominal rates specified in a column «for the belt which was in operation» tables 2.2.
At periodic check of a tension of a belt use the nominal rates specified in a column «at check» tables 2.2.

Tension measuring instrument – the type "A"

Tension measuring instrument – the type "A"
Fig. 2.17. A tension measuring instrument – the type "A"


Do not allow a contact the dial of a measuring instrument something at performance of measurements (fig. 2.17).

Tension measuring instrument – the type "V"
At performance of measurements turn the RESET handle in the direction specified by an arrow, and establish the index in the situation "RESET".

Tension measuring instrument – the type "V"
Fig. 2.18. A tension measuring instrument – the type "V"


If a measuring instrument of a tension to remove from a belt, the index remains in the situation corresponding to value of a tension. Consider indications after removal of a measuring instrument of a tension (fig. 2.18).

«previous page
2.1.11. Natyazhitel of a belt of a drive of hinged units
following page»
2.1.13. Adjustment of a belt of a drive of the generator