Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
2.1. Maintenance
2.2. Mechanical part (engine of 1,6 l)
2.2.1. Check of the block of cylinders
2.2.2. Removal and installation of a support of the power unit
2.2.3. Removal and engine and transmission installation assembled
2.2.4. Removal, check and installation of camshafts
2.2.5. Removal, check and installation of a belt of a drive of the mechanism of a gazoraspredeleniye
2.2.6. Dismantling, check and assembly of a cranked shaft
2.2.7. Removal, check and installation of a flywheel (MKPP) or plate of a drive of the hydrotransformer (AKPP)
2.2.8. Dismantling and assembly of shatunno-piston group
2.3. Mechanical part (engine of 1.8 l)
2.4. Cooling system
2.5. Greasing system
2.6. Power supply system
2.7. Control system, fuel system and system of decrease in toxicity
2.8. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 







2-2-2-snyatie-i-ustanovka-opory-silovogo-agregata.html

2.2.2. Removal and installation of a support of the power unit

Fastening of the power unit of the engine in volume of 1,6 l.
Fig. 2.23. Fastening of the power unit of the engine in volume of 1,6 l.



Removal

Engine fixing on a traverse
Fig. 2.24. Engine fixing on a traverse


Fix the engine on a traverse for arms of fastening and hang up it on the lift, then raise the engine assembled for unloading of support from weight of the power unit (fig. 2.24) a little.
Unscrew bolts of fastening of a lateral support of the engine (to the engine and a body).

Lateral support of the engine
Fig. 2.25. Lateral support of the engine


Remove a lateral support (assembled with an arm) from the engine (fig. 2.25).
On models from a 5-step manual transmission remove the sensor switch of lamps of a backing.

Bolt of fastening of a support of a transmission
Fig. 2.26. Bolt of fastening of a support of a transmission


Unscrew a bolt of fastening of a support of a transmission (to a basic arm of a check point) (fig. 2.26).
Take caps from within an antispray guard of the left wing. Unscrew bolts of fastening of an arm of a support of a transmission to a stretcher.
Remove a transmission support assembled.

Forward support of the engine
Fig. 2.27. Forward support of the engine


Remove a forward support of the engine assembled from a stretcher (fig. 2.27).

Back support of the engine
Fig. 2.28. Back support of the engine


Remove a back support of the engine assembled from a stretcher (fig. 2.28).

Installation
In order that the limiter of a support did not move, be convinced that it is correctly inserted into an internal tube of a support.

Scheme of installation of the limiter of a support
Fig. 2.29. Scheme of installation of the limiter of a support


Establish the support limiter into place, having convinced of correctness of its arrangement (fig. 2.29).

Installation of a forward support of the engine
Fig. 2.30. Installation of a forward support of the engine


Establish an engine support so that it settled down under the correct corner (And) to an arm (fig. 2.30).
Models with AKPP: 27–33 °.
Models with MKPP: 11–17 °.

Installation of a back support of the engine
Fig. 2.31. Installation of a back support of the engine


Establish an engine support so that it settled down under the correct corner (In) to an arm (fig. 2.31).
Models with AKPP: 30–36 °.
Models with MKPP: 17–23 °.

Installation of the basic plug of a stretcher

NOTE
Basic plugs of forward and back cross-section beams of a stretcher are directing.
Be convinced that basic plugs are correctly focused at installation.
In two places on the top surface of cross-section beams of a stretcher and the corresponding basic plugs there are labels (in the form of arrows) the installation directions.

Installation of basic plugs in internal tubes of cross-section beams of a stretcher
Fig. 2.32. Installation of basic plugs in internal tubes of cross-section beams of a stretcher


At installation of basic plugs in internal tubes of cross-section beams of a stretcher combine the arrow direction on the plug with the arrow direction on a cross-section beam of a stretcher (fig. 2.32).

NOTE
Check that before installation of the shooter on the basic plug it is located parallel to an arrow on a cross-section beam of a stretcher. Be convinced that the arrow direction on the established basic plug deviates no more than on ±3 ° the arrow direction on a cross-section beam of a stretcher.

«previous page
2.2.1. Check of the block of cylinders
following page»
2.2.3. Removal and engine and transmission installation assembled