Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. General information
8.2. External elements of a body
8.3. System of passive safety
8.4. Heater and conditioner
8.4.1. General information
8.4.2. Installation of connecting details
8.4.3. Depression creation in system
8.4.4. Removal and installation of a nave of the coupling and compressor pulley
8.4.5. Removal and installation of a winding of the electromagnetic coupling of the compressor
8.4.6. Removal and installation of an epiploon of a shaft of the compressor
8.5. Tables
9. Electric equipment schemes
 







8-4-6-snyatie-i-ustanovka-salnika-vala-kompressora.html

8.4.6. Removal and installation of an epiploon of a shaft of the compressor

Removal

Removal of a lock ring of an epiploon of a shaft
Fig. 8.77. Removal of a lock ring of an epiploon of a shaft



For replacement of an epiploon of a shaft of the compressor remove the compressor from the car and merge a coolant.
Remove from the compressor a coupling nave.
The pointed subject take a felt sealant from a compressor sock.
Carefully remove extraneous particles from a cavity of a sock of the compressor, having blown it the compressed air under low pressure. Then not fleecy fabric carefully clear an internal and external surface of a sock of the compressor of oil and dirt.
By means of a stripper take from a compressor sock a lock ring of an epiploon of a shaft.
1. Insert the stripper end into one of openings of a lock ring (a look And).
2. Turn a stripper so that its end and an opening of a lock ring settled down as it is possible closer to a compressor shaft (a look In).
3. Remove a lock ring, fast movement having pulled for a stripper up, holding its core at a wall of boring of a sock (a look C).

Installation of the special adaptation
Fig. 8.78. Installation of the special adaptation


Establish the adaptation for removal of an epiploon of a shaft (09977-33700) on a shaft of the compressor and shift it in a compressor sock to a contact with a shaft epiploon (fig. 8.78).
Get an adaptation head in internal diameter of an epiploon of a shaft. Holding a shestigrannik of the adaptation, expand an adaptation head in an epiploon, rotating the adaptation handle clockwise, then remove an epiploon, having pulled for the adaptation.

Installation
Check a protective ring on existence of agnails and other defects of a new epiploon. The damaged protective ring do not put.
Pure not fleecy fabric wipe a surface of a shaft and a nest under an epiploon in a compressor sock.
Ship a protective ring and an epiploon in pure compressor oil and establish an epiploon on a protective ring a working edge towards big diameter of a protective ring.

Epiploon installation on a compressor shaft
Fig. 8.79. Epiploon installation on a compressor shaft


Establish a protective ring with an epiploon for the end of a shaft of the compressor (fig. 8.79).

Opravka installation
Fig. 8.80. Opravka installation


Establish an opravka for an epiploon press fitting on an end face of a protective ring, then slowly shift an epiploon in a protective ring before landing in a nest (fig. 8.80).
Remove from the compressor an opravka for a press fitting of an epiploon and a protective ring.
Establish a new lock ring of an epiploon in boring of a sock of the compressor and by means of a stripper get it in a flute.
Check tightness of installation of an epiploon, having turned a shaft on 10 turns for a coupling nave.
Establish in a compressor sock new felt consolidation.
Establish on the compressor a coupling nave as it is specified above in this section.

«previous page
8.4.5. Removal and installation of a winding of the electromagnetic coupling of the compressor
following page»
8.5. Tables