Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
4.1. General information
4.2. Forward suspension bracket
4.2.1. Removal and installation of a forward amortizatorny rack
4.2.2. Dismantling, check and assembly of an amortizatorny rack
4.2.3. Removal, check and installation of the bottom lever of a suspension bracket
4.2.4. Removal, check and installation of the forward stabilizer of cross-section stability
4.3. Back suspension bracket
4.4. Tables
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 







4-2-3-snyatie-proverka-i-ustanovka-nizhnego-rychaga-podveski.html

4.2.3. Removal, check and installation of the bottom lever of a suspension bracket

Bottom lever of a suspension bracket
Fig. 4.25. Bottom lever of a suspension bracket



Removal
Remove a forward wheel.
Remove шплинт, unscrew a nut of fastening of a shaft of a drive of a wheel and remove a washer.
Weaken a nut of fastening of a spherical support of the bottom lever of a suspension bracket to a rotary fist do not turn on a nut completely.
Unscrew two bolts of fastening of a forward rack to a rotary fist (bottom).
Pull a wheel nave outside from the car and separate from it a shaft of a drive of a wheel.

Detachment of a spherical support of the bottom lever
Fig. 4.26. Detachment of a spherical support of the bottom lever


By means of the special tool (09568-34000) disconnect a spherical support of the bottom lever from the bottom lever (fig. 4.26).
Temporarily establish bolts of fastening of a forward rack to a rotary fist (bottom).
Unscrew a nut of fastening of a rack of the stabilizer.
Unscrew two bolts of fastening of And and G plugs of the bottom lever.
Remove the bottom lever of a suspension bracket assembled.

Installation

Tightening самоконтрящейся nuts
Fig. 4.27. Tightening самоконтрящейся nuts


At an inhaling of fastening of a rack of the stabilizer, holding the spherical hinge from a pro-collar a wrench (14 mm), tighten самоконтрящуюся a nut (fig. 4.27).

Replacement of a protective cover and spherical support of the bottom lever

Removal of a protective cover from a spherical support of the bottom lever
Fig. 4.28. Removal of a protective cover from a spherical support of the bottom lever


By means of a flat screw-driver remove a protective cover from a spherical support of the bottom lever (fig. 4.28).
Remove a lock ring.

Extraction of a spherical support from the bottom lever
Fig. 4.29. Extraction of a spherical support from the bottom lever


By means of a plastic hammer beat out a spherical support from the bottom lever (fig. 4.29).

Press fitting of a new spherical support in the bottom lever
Fig. 4.30. A press fitting of a new spherical support in the bottom lever


By means of the special tool (09545-11000) press a new spherical support in the bottom lever assembled (fig. 4.30).
Establish a lock ring.

Installation of a protective cover
Fig. 4.31. Installation of a protective cover


By means of the special tool (09545-21000) establish a protective cover (fig. 4.31).

Replacement of the plug "G" of the bottom lever

Installation of special tools on the bottom lever
Fig. 4.32. Installation of special tools on the bottom lever


Establish special tools (09545-02000, 09216-21200 and 09216-21100) on the bottom lever (fig. 4.32).
Vypressuyte plug.
Wet soap water the following details:
– external surface of the plug;
– an internal adjusting surface of the bottom lever under the plug.

Installation of the new plug on the bottom lever
Fig. 4.33. Installation of the new plug on the bottom lever


Establish the new plug on the bottom lever by means of the special tool (09216-21100 and 09624-34000) (fig. 4.33).

Press fitting of the plug "G" of the bottom lever
Fig. 4.34. Press fitting of the plug "G" of the bottom lever



NOTE
Press the plug "G" of the bottom lever, having arranged it at an angle, as is shown in drawing 4.34.

Check
Check rubber plugs on lack of wear or deformation.
Check the bottom lever on lack of a bend or cracks.
Check a protective cover of a spherical support on lack of cracks and damages.
Check all bolts on absence of deformation and damages.

Check of the moment of rotation
Fig. 4.35. Check of the moment of rotation


Check the moment of rotation of a finger of a spherical support of the bottom lever (fig. 4.35).
In the presence of cracks or ruptures of a protective cover of a spherical support replace a spherical support of the bottom lever assembled.
Several times shake a finger of a spherical support of the bottom lever.
Measure the moment of rotation of a finger of a spherical support of the bottom lever.
Nominal rate: 3,5–4 N · m.
If the moment of rotation exceeds the top limit of nominal rate, replace a spherical support of the bottom lever assembled.
If the rotation moment less bottom limit of nominal rate, is allowed repeated installation of this spherical support if there is no jamming and excessive люфт a hinge finger.

«previous page
4.2.2. Dismantling, check and assembly of an amortizatorny rack
following page»
4.2.4. Removal, check and installation of the forward stabilizer of cross-section stability