Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
4.1. General information
4.2. Forward suspension bracket
4.3. Back suspension bracket
4.3.1. Removal, dismantling, check and installation of a back amortizatorny rack
4.3.2. Removal and check of the longitudinal lever of a back suspension bracket
4.4. Tables
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 







4-3-2-snyatie-i-proverka-prodolnogo-rychaga-zadnejj-podveski.html

4.3.2. Removal and check of the longitudinal lever of a back suspension bracket

Longitudinal lever of a back suspension bracket
Fig. 4.51. Longitudinal lever of a back suspension bracket



Removal

Cable of the parking brake
Fig. 4.52. Cable of the parking brake


Disconnect a cable of the parking brake from an arm of the longitudinal lever of a back suspension bracket (fig. 4.52).

Bolt of fastening of the cross-section lever of a suspension bracket
Fig. 4.53. Bolt of fastening of the cross-section lever of a suspension bracket


Unscrew a bolt of fastening of the cross-section lever of a suspension bracket to a fist of a back wheel (fig. 4.53).
Support a back cross-section beam, having established a jack under its central part, then unscrew bolts of fastening of a cross-section beam to a body.
Remove a back cross-section beam together with cross-section levers of a suspension bracket.

Replacement of the plug of the longitudinal lever

Installation of the special tool on the longitudinal lever of a suspension bracket
Fig. 4.54. Installation of the special tool on the longitudinal lever of a suspension bracket


Establish the special tool (09551-25000) on the longitudinal lever of a suspension bracket (fig. 4.54).
Take the plug of the longitudinal lever.

Press fitting of the new plug in the longitudinal lever of a suspension bracket
Fig. 4.55. A press fitting of the new plug in the longitudinal lever of a suspension bracket


By means of the special tool (09551-25000) press the new plug in the longitudinal lever of a suspension bracket (fig. 4.55).

Plug arrangement concerning the lever
Fig. 4.56. A plug arrangement concerning the lever



NOTE
Press the plug, having arranged it concerning the lever, as is shown in drawing 4.56.

Replacement of the plug of the cross-section lever

Installation of the special tool on the cross-section lever of a suspension bracket
Fig. 4.57. Installation of the special tool on the cross-section lever of a suspension bracket


Establish the special tool (09545-28100 and 09545-25000) on the cross-section lever (fig. 4.57).
Take the plug of the cross-section lever.
Wet soap water of a surface of contact of the plug and the cross-section lever.
By means of the special tool (09545-25000) press the new plug in the cross-section lever.

Replacement of the back stabilizer of cross-section stability
Disconnect stabilizer racks from a back rack of a suspension bracket.

Removal of arms of fastening of the stabilizer
Fig. 4.58. Removal of arms of fastening of the stabilizer


Remove arms of fastening of the stabilizer (fig. 4.58).
Remove the stabilizer of cross-section stability.

Check

Check of the moment of rotation of the spherical hinge of a rack of the stabilizer
Fig. 4.59. Check of the moment of rotation of the spherical hinge of a rack of the stabilizer


Check the moment of rotation of the spherical hinge of a rack of the stabilizer (fig. 4.59).
In the presence of cracks or ruptures of a protective cover of the spherical hinge replace it and add greasing in the spherical hinge.
Several times shake a finger of the spherical hinge of a rack of the stabilizer.
Screw самоконтрящуюся a nut on a finger of the spherical hinge and then measure the moment of rotation of a finger.
Nominal rate: 3,5–4,0 N · m.
If the moment of rotation exceeds the top limit of nominal rate, replace a stabilizer rack.
If the rotation moment is considered less bottom limit of nominal rate, the spherical hinge suitable for further operation while there is no jamming and an excessive gap in the hinge.

«previous page
4.3.1. Removal, dismantling, check and installation of a back amortizatorny rack
following page»
4.4. Tables