Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
4.1. General information
4.2. Forward suspension bracket
4.3. Back suspension bracket
4.3.1. Removal, dismantling, check and installation of a back amortizatorny rack
4.3.2. Removal and check of the longitudinal lever of a back suspension bracket
4.4. Tables
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 





Как своими руками собрать сифон для умывальника?




4-3-1-snyatie-razborka-proverka-i-ustanovka-zadnejj-amortizatornojj-stojjki.html

4.3.1. Removal, dismantling, check and installation of a back amortizatorny rack

Fig. 4.42. Amortizatorny rack of a back suspension bracket



Removal
Remove back wheels.
Remove the safety cover located in a luggage carrier.
Disconnect a brake hose and a wire of the sensor of frequency of rotation of a wheel from a back rack of a suspension bracket.
Remove stabilizer racks.

Fig. 4.43. Bolts of fastening of a back rack of a suspension bracket


Unscrew two bolts of fastening of a back rack of a suspension bracket to a fist of a back wheel (fig. 4.43).

ATTENTION
Be careful, do not drop a back rack.

Remove a back rack assembled from the car.

Dismantling

Fig. 4.44. Compression of a spring of the shock-absorber


By means of the special tool (J38402, A-20 and A-50) compress a rack spring so that impact on cups of a spring was minimum (fig. 4.44).

NOTE
Do not apply the pneumatic tool (shock гайковерт).

Unscrew самоконтрящуюся a nut on the top end of a rod of the shock-absorber.
Remove a dempfiruyushchy support of a rack, the top cup of a spring, a spring and a protective cover from a rack assembled.

Check
Check a dempfiruyushchy support of a rack on lack of wear or damage.
Check rubber details on absence of damages or deterioration of a technical condition.
Check a spring and a rack assembled on lack of wear or deformation (a prosedaniye and decrease in rigidity).

Fig. 4.45. Shock-absorber check


Check the shock-absorber on lack of abnormal resistance to moving of a rod and extraneous noise (fig. 4.45).

Assembly

Fig. 4.46. Installation of the bottom pro-rate of a spring


Establish the bottom pro-rate of a spring so that ledges on it were combined with openings in the bottom cups of a spring (fig. 4.46).
Establish a protective cover on the shock-absorber.

Fig. 4.47. Spring compression


By means of the special tool (J38402, A-42) compress a spring (fig. 4.47).
Put forward a shock-absorber rod against the stop, establish the top cup of a spring and a dempfiruyuushchy support of a rack assembled.

Fig. 4.48. Combination of a flat part of a D-shaped opening of the top cup of a spring



NOTE
Combine a flat part of a D-shaped opening of the top cup of a spring with лыскои a bezrezjbovy part of a rod of the shock-absorber (fig. 4.48).


Fig. 4.49. Combination of the top and bottom rounds of a spring


Combine the top and bottom rounds of a spring with the corresponding dredging on the top and bottom cups of a spring of a rack, then temporarily tighten самоконтрящуюся a nut (fig. 4.49).

ATTENTION
Replace самоконтрящуюся a nut new after removal.


Fig. 4.50. Raspolozheniyedempfiruyuushchey of a rack support


At installation arrange a dempfiruyuushchy support of a rack so that its bolt was combined with a ledge of the top cup of a spring, as is shown in drawing 4.50.
Remove special the tool (J38402, A-20 and A-50).
Tighten самоконтрящуюся a nut the nominal moment of 40-55 N · m.

«previous page
4.3. Back suspension bracket
following page»
4.3.2. Removal and check of the longitudinal lever of a back suspension bracket