Hyundai Matrix service from 2002 to 2006 of release
1. Operation and car maintenance
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical transmission
3.3. Automatic transmission
3.4. Driving mechanism
3.4.1. Removal, check and installation of a shaft of a drive of a forward wheel
3.4.2. A shaft of a drive of a forward wheel (the CV JOINT with the jack of length (DOJ) and the CV JOINT «Birfilda BJ»)
3.4.3. Shaft of a drive of a forward wheel (CV JOINT «Tripod TJ»)
3.4.4. Nave of a forward wheel and rotary fist of a detail
3.4.5. Nave of a back wheel
3.5. Tables
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 







3-4-1-snyatie-proverka-i-ustanovka-vala-privoda-perednego-kolesa.html

3.4.1. Removal, check and installation of a shaft of a drive of a forward wheel

Shaft of a drive of a forward wheel
Fig. 3.115. Shaft of a drive of a forward wheel



Removal
Lift the car and remove a forward wheel.
Remove шплинт and unscrew a nut of fastening of a shaft of a drive of a wheel to a wheel nave.
Merge oil from a transmission.

Detachment of a shaft of a drive of a wheel
Fig. 3.116. Detachment of a shaft of a drive of a wheel


By means of a plastic hammer disconnect a shaft of a drive of a wheel from a wheel nave (fig. 3.116).
Pull a wheel nave outside from the car and separate from it a shaft of a drive of a wheel.

Detachment of a shaft of a drive of a wheel from a transmission
Fig. 3.117. A detachment of a shaft of a drive of a wheel from a transmission


Insert mount between a case of a transmission and the case of the CV JOINT of a shaft of a drive of a wheel, and then disconnect a shaft of a drive of a wheel from a transmission (fig. 3.117).

ATTENTION
Be careful at a detachment of a shaft of a drive of a wheel by means of mount, do not damage a case of a transmission and the shaft CV JOINT.
In order to avoid damage of an epiploon do not insert mount too deeply (at most 7 mm).
Do not extend a shaft of a drive of a wheel with considerable effort as similar operation will lead to damage of internal details of the CV JOINT «Birfilda of BJ» or «Tripod TJ» a shaft of a drive of a wheel (a rupture of a cover or bearing damage).

ATTENTION
By means of a special cap close an opening in a transmission for hit prevention in dirt and extraneous particles.
Reliably hold a shaft of a drive of a wheel.
Always replace a lock ring (retainer ring) after a detachment of a shaft of a drive of a wheel from a transmission.

Check

Check of a power shaft
Fig. 3.118. Check of a power shaft



Check a protective cover of the CV JOINT of a shaft of a drive of a wheel on absence of damages and deterioration of a technical condition.
Check spherical hinges on lack of the increased wear and mobility.
Check a shlitsevy part of a shaft of a drive of a wheel (and naves) on lack of the increased wear or damages.
Check a dynamic damper on absence of damages or cracks.

Installation
Grease with transmission oil of a shlitsa of a shaft of a drive of a wheel and a surface of contact of the case of differential (in a transmission).
Before installation of a shaft of a drive of a wheel arrange a lock ring so that its lock was directed down.
After installation of a shaft of a drive of a wheel check that the shaft is reliably fixed and cannot be removed by hand.

Installation of a washer and nut of fastening of a shaft of a drive
Fig. 3.119. Installation of a washer and nut of fastening of a shaft of a drive


Establish a washer the convex party outside, then establish a nut of fastening of a shaft of a drive of a wheel and шплинт (fig. 3.119).
Always replace самоконтрящуюся a nut of fastening of a shaft of a drive of a wheel and шплинт new after each detachment of a shaft from a nave.

«previous page
3.4. Driving mechanism
following page»
3.4.2. A shaft of a drive of a forward wheel (the CV JOINT with the jack of length (DOJ) and the CV JOINT «Birfilda BJ»)